Product Guides

SONOFF Products Integration Guide for SmartThings & Driver Installation

SONOFF Products Integration Guide for SmartThings & Driver Installation

In response to user feedback and to enhance the accessibility of our products, we’re thrilled to introduce two methods for seamlessly integrating SONOFF products into the SmartThings ecosystem. These methods empower users to effortlessly integrate our products into their SmartThings ecosystems for control.

Method 1: Cloud Integration

For users who primarily use the eWeLink App, we recommend considering this method first. If you’re using Zigbee products, please note that you’ll require a SONOFF Zigbee gateway (such as ZBBridge-P or NSPanel Pro). Detailed steps for cloud integration can be found here: https://ewelink.cc/ewelink-works-with-smartthings/

Method 2: Zigbee Direct Connection

If the SmartThings App is your primary platform and you already have a SmartThings gateway, you can choose this method. We’ve provided links to the drivers necessary for integrating SONOFF Zigbee products with the SmartThings gateway at the end of this article.

Installation steps:

1. Access the Driver URL link.

2. Sign in with your Samsung account.


3. Click ‘Enroll’, it may take up to a minute.
4. Click ‘Available Drivers’


5. Click ‘Install’
6. Now the installation of the device driver has been completed.


7. Open the SmartThings App, and scan for nearby devices.
8. Then long press the device’s pairing button for 5 sec to enter pairing mode.



9. Please wait until the device addition process is complete.


Drivers URL link

Most SONOFF Zigbee products support integration with the Samsung SmartThings platform.

👉 For the Drive URL Link, please visit the SONOFF Help Center and locate it under the "Introduction" section of the specific product page.

The Drive URL Link and supported capabilities for certain popular products are listed in the table below: 

Product

Driver URL

Features

MINI-ZBD

https://bestow-regional.api.smartthings.com/invite/kVlnwR6yLoj4

●ON/OFF
●Detach Relay
●Power-on State

TRV-ZBT

https://bestow-regional.api.smartthings.com/invite/d429GN7o5Djo

●Remote Temp Control
●3 Operating Modes Available (Schedule + Manual + Anti-freeze)
●Battery Level Indication


TRVZB

https://bestow-regional.api.smartthings.com/invite/gpjGAnZJoX24

●Device Mode
●Current Temperature
●Temperature Setting
●Heating State
●Battery State

SNZB-02LD

https://bestow-regional.api.smartthings.com/invite/5z2RpqyNwzj1

●Temperature Detection
●Temperature Calibration
●Battery State

SNZB-02WD

https://bestow-regional.api.smartthings.com/invite/5z2RpqyNwzj1

●Tem. &Hum. Detection
●Tem. &Hum. Calibration
●Battery State

SNZB-03P

https://bestow-regional.api.smartthings.com/invite/qWjBdD7nAw2y

●Motion Detection
●Battery State
●Detection Duration
●Illuminance Detection (Bright & Dim)

SNZB-03PR2

 https://bestow-regional.api.smartthings.com/invite/WY2Wb3edYmMr

●Motion Detection
●Battery State
●Detection Duration
●Illuminance Detection (Lux)

●Illumination Offset

SNZB-04P

https://bestow-regional.api.smartthings.com/invite/r3MymG3kBbMp

●Open & Close Detection
●Battery State
●Tamper-proof State

SNZB-05P

https://bestow-regional.api.smartthings.com/invite/Pw2DLAr7w823

●Leaking Detection
●Battery State

SNZB-06P

https://bestow-regional.api.smartthings.com/invite/qWjBdD7nAw2y

●Motion Detection
(Appears as a motion sensor but retains the functionality of a human presence sensor)
●Detection Duration
●Detection Sensitivity
●Illuminance (Bright & Dim)

SNZB-01M

●Single/Double/Triple-Click, Long Press




Reading next

Blink! Blink! SONOFF Product is “Talking” to You
SONOFF Zigbee Smart Curtain Motor

25 comments

Joanna Z

Joanna Z

Reply to Hans: Hi, the driver URLs for the SNZB-02LD and SNZB-02WD are indeed the same, so the link is not incorrect. Both models use the same main control chip and Zigbee communication logic, so the gateway uses one common driver script to identify them. “SNZB-02LWDs” in the URL is only the server-side filename. This driver has been verified with the SNZB-02LD and can connect to a SmartThings hub normally.

Joanna Z

Joanna Z

Reply to Jesper: Hi, we currently have no plans to develop a custom Samsung driver for the MINI-ZBDIM.

Hans

Hans

The driver URLs above are the same for SNZB-02LD and SNZB-02WD. It seems the one for SNZB-02LD may be incorrect (it links to channel SONOFF SNZB-02LWDs). Is there a correct URL for SNZB-02LD?

Jesper

Jesper

Hello, have problems with the MINI-ZBDIM in SmartThings and external buttons. Everything works in the SmartThings app, but not using the external buttons. Do you have any edge drivers for this?

Joanna Z

Joanna Z

Reply to 允守 劉: 您可以查看以下 SmartThings 驅動程式,將 SNZB-06P24 連接到 SmartThings:
https://bestow-regional.api.smartthings.com/invite/kVM5d0J3r7j5

Leave a comment

All comments are moderated before being published.

This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.